Blue and Gold Wedding Cake Tutorial

Blue and Gold Wedding Cake Cake Tutorial by Mark Desgrosseilliers from Morsels by Mark

In this blue and gold wedding cake tutorial, I’m going to show you how easy it is to make a stunning wedding cake that will wow your customers and their guests while saving you some time so you can see a bigger profit in terms of time-saving.

Tools and Supplies:

  • Flight of Fancy Silicone Onlay®
  • Classic Pearl Swag Mold
  • Classic Pearl Drop Mold
  • Classic Pearl Border Mold
  • Turntable Fondant (white, blue, gold)
  • Tylose powder Disco Dust by The Sugar Art (gold)
  • Sterling Pearl Dust by The Sugar Art (Blue Belle, Super Pearl, Wedding Gold)
  • Elite Petal Dust by The Sugar Art (Royal Blue, Mona Lisa)
  • Foam paint brush
  • Blush brush
  • Fine detail brush (morselsbymark.weebly.com)
  • Sugar Glue (I thin down piping gel or clear corn syrup with water)
  • Confectioner’s Glaze (and thinner for cleaning brushes)
  • Shortening
  • Corn Starch
  • Scalpel or exacto blade
  • Gum paste Garden Rose*
  • Prepared cakes (I used a 6×4, 8×6 and 10×4) 12” cake drum
blue and gold wedding cake

Instructions

1. Start by coloring your base fondant. To get the sapphire color I used, I started with blue fondant. Using Mona Lisa and Royal Blue Elite colors (about 1 tsp each) and 2 Tbsp vegetable shortening, I made a paste color that I added to the fondant and kneaded it in. This allows me to get a deeper color without having to use too much gel color and change the consistency. Mixing powder with shortening helps disperse the color more evenly and conditions the fondant at the same time.

Gather your tools and supplies
Mix colors together for your fondant
Mix Color into fondant

2. Allow the fondant to rest an hour or so, then cover your top and bottom tier in the sapphire fondant and the middle tier in white.

3. Using Blue Belle Sterling Pearl, a touch of super pearl and Mona Lisa Elite color, make a custom pearl dust to match your fondant. Place half of your dust in another container and set aside. Add enough vodka to make a wash (think the consistency of 2% milk).

Put colored dust into a pan
Using dust and vodka, create a wash for your fondant

4. Place your bottom tier on a turntable.

5. Use a foam paint brush and give your cake a coat of the wash.  Repeat for top tier and give each a second coat after the first is dry.  Allow to dry to the touch.

Brush the wash onto the side of the cake

6. Load some sapphire dust on a blush brush and remove the excess.  Apply to your cakes in a circular motion – this will help even out any brush strokes you may have.

7. Make gold fondant by starting with ivory fondant (1 lb) and add 3 drops golden yellow and 1 drop brown gel color (This will make painting gold very easy later on). Knead in 1 tsp tylose and set aside 1 hour.

8. I use a Kitchen Aid Roller to roll my fondant for my Silicone Onlays®; I like going to a 3 setting.

9. Place a piece of fondant onto the onlay that has been lightly dusted with cornstarch with the excess removed.  I use my fingers to lightly get the fondant in place, then lightly press with a fondant smoother to get my pattern cut.

10. Use a sharp tool to remove the “negative spaces” from your Silicone Onlay®

Fill Flight of Fancy Silicone Onlay® with fondant and remove unwanted

11. Brush your fondant pieces with gum glue and apply to bottom tier.

Apply Flight of Fancy Silicone Onlay® to the side of the cake

12. Brush a 1 inch perimeter of gum glue along the outer edge of your cake drum.  Place a piece of rolled out gold fondant on top.  Trim excess and remove center.

Make a ring of fondant around the top of your cake stand

13. Brush fondant on board with gum glue lightly and apply gold disco dust.  Remove excess and repeat until fondant is covered in glitter.

Dust the ring with glitter

14. Spray glitter with spray glaze.  Attach bottom tier using hot glue (If using real cake, your cake should be on a thin cardboard cakeboard).

15. Stack remaining tiers adding support with dowels as needed.

16. Mold decorations for the top tier using gold fondant.

Pack fondant into the Classic Pearl Swag Mold
Pack fondant into the Classic Pearl Drop Mold

17. Attach to top tier by lightly brushing gum glue to the back of decoration.

Attach Classic Pearl Swag Mold and Classic Pearl Drop Mold to the top edge of the top tier

18. To make a single strand of pearls, use a scalpel to cut the strands apart (I suggest letting the molded piece lay out on the counter for five minutes before cutting to let it firm up a bit)

Cut Classic Pearl Border Mold into long single strands

19. Using Wedding Gold Sterling Pearl, add some confectioners glaze to make a paint (consistency of cream) and paint all of your gold pieces.  I use an ultra-fine detailing brush to get into every corner of my pieces.

Paint highlights on the pearls

20. Finish your cake by adding some white sugar garden roses* highlighted with the gold paint.

Mark Desgroseilliers headshot

There you have it! A beautiful, 3 tiered cake that took very little time to make, but looks like you spent days on it!

This blue and gold wedding cake tutorial was created by Mark Desgrosseilliers from Morsels by Mark. *The roses are taught in his DVD Timeless Wedding Flowers. Mark is an award-winning Montreal based cake designer who is the administrator for the local chapter of the Canadian Cake Decorator’s Guild. He loves sharing his passion for sugar and teaches internationally.  Visit him online at: http://morselsbymark.weebly.com/